Understanding & Fixing HDMI Noise
HDMI noise issues can be of two flavors, ingress (entering) or egress (exiting). In HDMI we are concerned about both.
Poor grounding can also be reasons for ingress to overtake the signal and cause intermittent HDMI A/V. When running long lengths of cable there will always be some potential difference along these wires from beginning to the end. I don’t care if it is video, audio, DC, data, or ground. By the time you reach your end destination there will always be some resistance in the line and this resistance can raise havoc with any type of signal. One of the nice things about RMC is that it provides a wonderful return path for ground because it is so massive in size.
But many installs don’t have that luxury of using pipe so you must proceed with some caution as you meander your way through the congestion of other cables that may be in the walls already, especially those that are prone to emitting noise. Most of the noise-emitting devices I mentioned previously are AC related, which means you need to stay as far away as possible from AC lines such as Romex.
Don’t be as concerned with BX since it’s shielded and grounded already. But again, we don’t typically see this in residential applications. If you must go near these cables don’t run them side-by-side; cross over and continue. Perpendicular crossing is the best and will reduce the amount of noise induced to the cable.
More HDMI News
DVDO Air3 Delivers WirelessHD from HDMI Sources
Genius! Vanco ‘Boost’ Adapter Converts Old HDMI Cables to HDBaseT
4K Content over HDMI, HDBaseT Creates Challenges
Neat-O: IP-Based Control, MoCA Make Retrofit Easier
All HDMI News
Category 5 and 6
Most traditional ATDs (baluns) that get a fair amount of use can be purchased with a single or dual power supply (wall warts). Because of convenience, single supply systems are gaining more popularity. With only one power supply to deal with, it just makes the installs neater and easier. However, in many cases these products have electronics on both sides (transmitting and receiving). So when you power up with just one power supply the DC and the ground wires must be carried over the length of the cable to support the opposite end. The DC level will drop just by way of load and distance.
But there is little that can be done with the ground. It must return not only the DC component but must also act as the return for signal lines. As this resistance goes up, it reduces the effectiveness of the ground that connects source to sink. This high impedance ground can also add to the susceptibility for ingress interferences. The more wires used for ground the better.
Cut it Off at the Source
Is there a way to stop these problems at the source if you can’t stop the noise entering the cable? Yes and no. The first thing to do is find the hardware that is causing the noise. You should know the major culprits that cause these problems to begin with.
If intermittent HDMI occurs, you need to include these interference transmissions as part of your troubleshooting list. First, by way of trial and error, eliminate the ones that could be causing the problem. Just turn it off and check it again. By pure elimination you may be able to find the problem. If you need more help, get a cheap AM radio. Tune to mid band and turn the volume up. Since these noises are usually AC related, the radio will pick up low frequencies. If the screen drops out as you hear loud noise or static, you’ve probably found your problem.
Now use it as a field strength meter and locate the hardware that is causing the problem. The closer you are, the louder it will get. When you find it, determine what kind of noise it is and put some AC suppression on it. You may want to bring in a licensed electrician to limit your liability.
2019 State of the Industry Special Report - CE Pro Download
The custom electronics industry saw a healthy 8 percent growth rate in 2018, down slightly from the blazing 11 percent growth in 2017 but still admiringly strong. Our 2019 State of the Industry indicates that readers expect to see even more growth in 2019. Get your copy today.
Jeff Boccaccio is president of DPL Labs. Jeff can be reached at firstname.lastname@example.org. Have a suggestion or a topic you want to read more about? Email Jeff at email@example.com
Follow Jeff on social media:
HDMI4 ‘Bohemian Rhapsody’ Scenes Perfect For Dolby Atmos Demos
Vanco Evolution Switches and Extenders Handle 4K, HDBaseT
Metra to Showcase 50+ HDMI Cables at ISE 2019
KanexPro 4K Wall Plate Switcher Series Supports HDMI 2.0, USB-C
FIBBR 4-in-1 HDMI Cable Supports Next Gen 8K Video Signals
View more on HDMI